大板瓷砖装饰效果简洁气派，留缝少，切割方式多使其运用更加广泛。So，大板如何铺贴效果更佳呢？这里有份详细的大板铺贴讲解，建议收藏！
The decorative effect of the large tile is simple and elegant, with fewer seams and more cutting methods, which makes it more widely used. So, how to lay the board better? Here is a detailed explanation of the large board, it is recommended to collect!
01、准备工作
铺贴之前，我们需要准备好铺贴大规格瓷砖的工具，如粘结剂、三孔玻璃吸、锯齿状抹灰器、灰匙、橡胶锤、靠尺、找平钳套装、清洁抹布等。
Before paving, we need to prepare tools for laying large-sized tiles, such as adhesives, three-hole glass suction, serrated plaster, ash spoon, rubber hammer, ruler, leveling pliers set, cleaning rag, etc.
02、铺贴前检查
施工图纸校对、平整度检测、垂直度检测、水电管线铺设检测以及防水等工作，这是确保最佳的瓷砖铺设效果、打造高品质生活空间的前置条件。
Construction drawings proofreading, flatness detection, verticality detection, water and electricity pipeline laying detection and waterproofing are the prerequisites for ensuring the best tile laying effect and creating a high-quality living space.
03、基面处理
清除基层浮灰、油等污渍，以免会影响粘结剂的粘合度。基面内部必须保持平整，高低不平或表面粗糙的地方可以使用水泥砂浆抹平，同时充分湿润施工基面，防止空鼓。
Remove the dirt, oil and other stains from the base, so as not to affect the adhesion of the adhesive. The interior of the base surface must be kept flat. Cement mortar can be used to smooth the uneven or rough surface, and at the same time fully wet the construction base to prevent emptying.
04、调制粘结剂
1. 将自来水加入搅拌桶，再将粘贴剂逐量加入，用低速电动搅拌器搅拌均匀成糊状。
2. 水化（静置）5-10min后进行二次搅拌3min左右即可使用，(水化后的粘结剂不可加水或粘结剂干粉再次搅拌，否则影响粘结效果)
3. 用批灰刀挑起搅拌均匀的粘结剂后倒置，粘结剂在5秒左右从批灰刀上坠落，此时的粘结剂的粘稠度为最佳。
注意：粘结剂在制备完毕后需静置5-10min。粘结剂的可操作时间常温下为2小时。（可操作时间指制备完毕到使用的时间）。
1. Add tap water to the mixing tank, and then add the adhesive one by one, using a low-speed electric mixer to mix evenly into a paste.
2. After hydration (stand still) for 5-10 minutes, it can be used after about 2 minutes of secondary stirring. (The hydrated adhesive cannot be added with water or the dry powder of the adhesive is stirred again, otherwise it will affect the bonding effect)
3. Use the batch ash knife to pick up the evenly mixed adhesive and turn it upside down. The adhesive falls from the batch ash knife in about 5 seconds. At this time, the viscosity of the adhesive is the best.
Note: The adhesive needs to stand for 5-10min after preparation. The operable time of the adhesive is 2 hours at room temperature. (Operable time refers to the time from preparation to use).
05、涂抹粘结剂
在地面均匀铺上一层粘结剂，形成半干的一层，再次用粘结剂填平表面凹凸处，厚度为0.5CM左右；适当条件下，可同时将粘结剂均匀地抹在瓷砖背面，涂抹饱满。
Spread a layer of adhesive evenly on the ground to form a semi-dry layer, and then fill the surface irregularities with the adhesive again, the thickness is about 0.5CM; under appropriate conditions, the adhesive can be evenly applied to the tiles at the same time On the back, smear full.
瓷砖背涂时，需用齿状抹灰器均匀的将粘结剂抹成条齿状。注意刮时基面与大板需朝同一方向刮齿纹，便于空气排出，避免空鼓而造成开裂脱落现象。
When the tiles are back-coated, the adhesive needs to be evenly applied to the teeth with a tooth plaster. Note that the base surface and the large board should be scraped in the same direction when scraping, which is convenient for the air to escape and avoid the phenomenon of cracking and shedding caused by the hollow drum.
06、搬运铺贴
用三孔玻璃吸工具平抬大板平移施工位置，放置到铺好粘结剂的基面上，至少需要2名工人进行搬运；面积更大的使用移动架搬运。
Use a three-hole glass suction tool to lift the large plate and move it to the construction position, and place it on the base surface where the adhesive is paved. At least 2 workers are required to carry it; for a larger area, use a moving frame to carry it.
大板的粘贴顺序为“自内而外”，必须保证粘结剂的饱满度，避免出现空鼓现象。根据设计的要求，应使用适当规格的定位器，以保证留缝的尺寸满足设计要求，并保证留缝宽度的一致。
The order of pasting the large board is "from the inside out", and the fullness of the adhesive must be ensured to avoid emptying. According to the design requirements, the locator with appropriate specifications should be used to ensure that the size of the remaining seam meets the design requirements and that the width of the remaining seam is consistent.
07、铺平压紧
将瓷砖平整地铺贴在基层上，使用橡胶锤或塑胶平板将瓷砖拍实铺平，便于大板瓷砖与基面之间满浆，排出气泡，以免产生空鼓现象。
注意已经铺贴完成的大板瓷砖表面拍打时一定要控制好力度，拍打方向可以遵循从瓷砖中间往四周扩散进行。用橡胶锤或塑胶平板把砖面敲平整的同时，以靠尺测量，确保瓷砖铺贴水平。
Lay the tile flat on the base layer, use a rubber hammer or a plastic plate to flatten the tile, so that the large board ceramic tile and the base surface are full of slurry, and the air bubbles are discharged to avoid emptying.
Note that the surface of the large slab tile that has been paved must be well controlled. The direction of the tapping can follow the diffusion from the middle of the tile to the surrounding. Use a rubber hammer or a plastic plate to knock the brick surface flat and measure with a ruler to ensure that the tiles are level.
08、找平处理
在已定位好的大板边缘周围每60cm左右插入找平器底座，检验平整后插入找平楔子并夹紧找平器，调节相邻大板的表面平整度，并将大板间隙调整为2mm左右，以便后续美缝剂处理。
Insert the leveler base around every 60cm around the edge of the positioned large board, insert the leveling wedge and clamp the leveler after checking the leveling, adjust the surface flatness of the adjacent large board, and adjust the large board gap to about 2mm, so that Subsequent beauty agent treatment.
09、空鼓检查
铺贴一个小时后，可用橡胶锤敲击砖面，检查是否出现空鼓现象。若听到“空空”声的地砖，必须设法重新铺贴。瓷砖铺贴结束后24小时，可进行嵌缝施工。
After paving for an hour, you can use a rubber hammer to hit the brick surface to check whether there is hollow phenomenon. If you hear "empty" sound tiles, you must try to re-paving. The caulking construction can be carried out 24 hours after the tile laying is finished.
10、砖面清洁
及时将残留的粘结剂和灰尘沙土清洁干净，铺贴24小时后才能进行美缝。美缝可使用海绵填缝刮刀对瓷砖缝隙进行美缝处理，等待填缝剂固化后，清理多余的美缝剂。
Clean the residual adhesive and dust, sand and dirt in time, and beautify the seam only after 24 hours of application. Beauty joints can use a sponge caulking spatula to perform beauty joint treatment on the gaps of ceramic tiles.
11、施工小贴士
1.在大板铺贴施工时，建议使用专业的粘结剂，而非传统【水泥】，因为使用水泥铺贴大板容易造成空鼓现象。
2.铺贴厚度以5-7毫米为宜，粘结剂过厚容易导致后期脱落。
3.铺贴高度如超过7.2米，建议使用干挂法。
4.建议使用美缝剂/瓷缝剂，能够增加瓷砖的整体美观感，不会霉变。
完成这些工序后，整个大板的铺贴操作步骤就圆满的完成啦！
1. In the construction of large slabs, it is recommended to use professional adhesives instead of traditional [cement], because the use of cement to lay large slabs can easily cause hollowing.
2. The thickness of the paving should be 5-7 mm, too thick adhesive can easily lead to falling off later.
3. If the paving height exceeds 7.2 meters, the dry hanging method is recommended.
4. It is recommended to use the beauty jointing agent/porcelain jointing agent, which can increase the overall aesthetic appearance of the ceramic tile without being moldy.
After completing these procedures, the entire slab laying operation step is successfully completed!
大板装卸物流指导
1、为确保产品完好无损，可以按照以下装卸与物流标准进行操作。
△使用2吨以上叉车并用加长叉，叉长要求达到1.2米
△每次只能叉一托，竖向必须用加长叉
△不同规格不可压放
2、装车注意
◎ 按要求打好简易托，确保产品完好无损，装车前拍照
◎ 运输车辆吨位是否符合装车运输标准
◎ 装车叉车吨位与叉长需符合标准
◎ 货物装车需按各规格装车标准严格执行，运输途中不能叠放其他货物
3、运输注意
◎ 属于易碎品，勿踩、勿压
◎ 货物装车后不能进行二次卸载与重新装车，避免破损
◎ 车速稳定，匀速行驶
4、卸车注意
◎ 卸货前拍照，卸货叉车吨位与叉长需符合标准
